FreeBSD manual
download PDF document: if_run.4.pdf
RUN(4) FreeBSD Kernel Interfaces Manual RUN(4)
NAME
run - Ralink Technology USB IEEE 802.11a/g/n wireless network device
SYNOPSIS
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
device ehci
device uhci
device ohci
device usb
device run
device wlan
device wlan_amrr
Firmware is also needed, and provided by:
device runfw
Alternatively, to load the driver as a module at boot time, place the
following lines in loader.conf(5):
if_run_load="YES"
runfw_load="YES"
DESCRIPTION
The run driver supports USB 2.0 wireless adapters based on the Ralink
RT2700U, RT2800U, RT3000U and RT3900E chipsets.
The RT2700U chipset consists of two integrated chips, an RT2770 MAC/BBP
and an RT2720 (1T2R) or RT2750 (dual-band 1T2R) radio transceiver.
The RT2800U chipset consists of two integrated chips, an RT2870 MAC/BBP
and an RT2820 (2T3R) or RT2850 (dual-band 2T3R) radio transceiver.
The RT3000U is a single-chip solution based on an RT3070 MAC/BBP and an
RT3020 (1T1R), RT3021 (1T2R) or RT3022 (2T2R) single-band radio
transceiver.
The RT3900E is a single-chip USB 2.0 802.11n solution. The MAC/Baseband
Processor can be an RT3593, RT5390, RT5392 or an RT5592. The radio can
be an RT3053, RT5370, RT5372 or an RT5572. The RT3053 chip operates in
the 2GHz and 5GHz spectra and supports up to 3 transmit paths and 3
receiver paths (3T3R). The RT5370 chip operates in the 2GHz spectrum and
supports 1 transmit path and 1 receiver path (1T1R). The RT5372 chip
operates in the 2GHz spectrum and supports up to 2 transmit paths and 2
receiver paths (2T2R). The RT5572 chip operates in the 2GHz and 5GHz
spectra and supports up to 2 transmit paths and 2 receiver paths (2T2R).
These are the modes the run driver can operate in:
BSS mode Also known as infrastructure mode, this is used when
associating with an access point, through which all
traffic passes. This mode is the default.
Host AP mode In this mode the driver acts as an access point (base
station) for other cards.
The run driver can be configured to use Wired Equivalent Privacy (WEP) or
Wi-Fi Protected Access (WPA-PSK and WPA2-PSK). WPA is the de facto
encryption standard for wireless networks. It is strongly recommended
that WEP not be used as the sole mechanism to secure wireless
communication, due to serious weaknesses in it. The run driver offloads
both encryption and decryption of data frames to the hardware for the
WEP40, WEP104, TKIP(+MIC) and CCMP ciphers.
The run driver can be configured at runtime with ifconfig(8).
HARDWARE
The run driver supports the following wireless adapters:
Airlink101 AWLL6090
ASUS USB-N11
ASUS USB-N13 ver. A1
ASUS USB-N14
ASUS USB-N66
ASUS WL-160N
Belkin F5D8051 ver 3000
Belkin F5D8053
Belkin F5D8055
Belkin F6D4050 ver 1
Belkin F9L1103
Buffalo WLI-UC-AG300N
Buffalo WLI-UC-G300HP
Buffalo WLI-UC-G300N
Buffalo WLI-UC-G301N
Buffalo WLI-UC-GN
Buffalo WLI-UC-GNM
Buffalo WLI-UC-GNM2
Corega CG-WLUSB2GNL
Corega CG-WLUSB2GNR
Corega CG-WLUSB300AGN
Corega CG-WLUSB300GNM
D-Link DWA-130 rev B1
D-Link DWA-130 rev F1
D-Link DWA-140 rev B1, B2, B3, D1
D-Link DWA-160 rev B2
D-Link DWA-162
DrayTek Vigor N61
Edimax EW-7711UAn
Edimax EW-7711UTn
Edimax EW-7717Un
Edimax EW-7718Un
Edimax EW-7733UnD
Gigabyte GN-WB30N
Gigabyte GN-WB31N
Gigabyte GN-WB32L
Hawking HWDN1
Hawking HWUN1
Hawking HWUN2
Hercules HWNU-300
Linksys WUSB54GC v3
Linksys WUSB600N
Logitec LAN-W150N/U2
Mvix Nubbin MS-811N
Panda Wireless PAU06
Planex GW-USMicroN
Sweex LW303
Sweex LW313
TP-LINK TL-WDN3200
TP-LINK TL-WN321G v4
TP-LINK TL-WN727N v3
Unex DNUR-81
Unex DNUR-82
ZyXEL NWD2705
ZyXEL NWD210N
ZyXEL NWD270N
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev run0 inet 192.168.0.20 \
netmask 0xffffff00
Join a specific BSS network with network name "my_net":
ifconfig wlan create wlandev run0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev run0 ssid my_net \
wepmode on wepkey 0x1234567890 weptxkey 1 up
Join a specific BSS network with 128-bit WEP encryption:
ifconfig wlan create wlandev run0 wlanmode adhoc ssid my_net \
wepmode on wepkey 0x01020304050607080910111213 weptxkey 1
DIAGNOSTICS
run%d: failed load firmware of file runfw For some reason, the driver
was unable to read the microcode file from the filesystem. The file
might be missing or corrupted.
run%d: could not load 8051 microcode An error occurred while attempting
to upload the microcode to the onboard 8051 microcontroller unit.
run%d: device timeout A frame dispatched to the hardware for
transmission did not complete in time. The driver will reset the
hardware. This should not happen.
SEE ALSO
intro(4), netintro(4), runfw(4), usb(4), wlan(4), wlan_amrr(4),
wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), wlan_xauth(4), hostapd(8),
ifconfig(8), wpa_supplicant(8)
HISTORY
The run driver first appeared in OpenBSD 4.5.
AUTHORS
The run driver was written by Damien Bergamini <damien@openbsd.org>.
CAVEATS
The run driver supports some of the 11n capabilities found in the RT2800,
RT3000 and RT3900 chipsets.
FreeBSD 14.0-RELEASE-p11 May 23, 2021 FreeBSD 14.0-RELEASE-p11